Practising Safety Management Skills: Your Questions Answered

People who work with a safety management system (SMS) in aviation are often told to “be more vigilant” or “report more”. Neither instruction explains how to get better at the underlying skills: noticing a hazard, describing it clearly, and judging how serious it is. This FAQ answers the questions practitioners ask most often about building those skills through deliberate practice, which means a brief exercise on one soft spot, a frank comment from someone who watched, and one small change. The content is general and informational. Your organisation’s own manuals, regulators and training providers define what is required where you work.

What does “practise deliberately” mean for safety management work?

It means treating each core SMS skill as something that can be trained in isolation, rather than assuming experience alone will sharpen it. Long periods of routine work tend to build habits: the same walk-through, the same report template, the same assumptions. Habits are efficient, but they can hide blind spots. A drill picks one blind spot, gives you a controlled opportunity to exercise it, and delivers feedback while the attempt is still fresh.

Which SMS skills are worth drilling?

Four tend to repay attention:

  • Hazard spotting: noticing conditions or practices that could contribute to harm.
  • Report writing: describing an event or concern so that a reader who was not there can understand it.
  • Risk judgement: estimating likelihood and severity consistently, using your organisation’s own matrix.
  • Briefing and follow-up: communicating a safety point to colleagues in a way they remember.

How do I drill hazard spotting?

Choose one workplace area and spend five minutes looking at it with a single question, such as “What could go wrong with how tools or equipment are stored here?” Write down up to three observations, then compare them with a colleague who looked at the same area independently. The feedback is in the difference: what did they see that you missed? Next session, change the question, for example to lighting or signage, and repeat. Narrowing the lens is what makes the exercise hard enough to teach you something.

How do I drill report writing?

Take a short, non-sensitive scenario, either invented or from published safety material, and write a report on it in ten minutes. Then swap with a colleague and ask them to answer three questions using only your text: what happened, where, and what do you think should be looked at? Anything they cannot answer shows the gap. Rewrite only that part. Over several rounds you will notice recurring omissions, such as missing location detail or a vague time reference, and those become your standing targets.

How do I drill risk judgement?

Use your organisation’s own matrix, never a generic one. Select five hypothetical situations and score each independently. Have a colleague do the same, then discuss only the scores that differ by more than one step. The aim is not to reach the “right” number but to understand why two careful people disagreed. Often the cause is an unstated assumption about frequency, and naming it is the learning. Run this drill monthly rather than daily; judgement benefits from spacing.

What makes feedback useful in this context?

Three qualities matter: it is specific, it is timely, and it describes the work rather than the person. “The location line is missing” is better than “you were vague”. It should arrive within minutes of the attempt wherever possible. And it should be limited to one or two points, since a long list tends to produce no change at all. If you are the one giving feedback, ask yourself whether the person could act on it in the next ten minutes.

Who can provide feedback if I work alone?

Consider a safety officer, a training provider, a peer in another department, or a mentor from a related industry. People in other technical fields face the same question. Engineers developing DevOps skills, for example, often browse the DevOpsTrainer listing of DevOps instructors, coaches and trainers to find an outside reviewer, and the habit transfers directly: look for someone who will react to your actual output and be candid about it.

How do I drill a safety briefing?

Pick one safety point and deliver it in ninety seconds to a colleague who plays a busy team member. Afterwards, ask them to repeat back the one thing they remember. If it is not the point you intended, the message was buried. Trim the briefing to a single sentence of substance, give one concrete example, and deliver it again. Repeat with a different point on another day. The feedback is immediate and measurable: either the listener can say it back or they cannot.

What if colleagues are sceptical about practising like this?

Scepticism is common, usually because people associate “practice” with training courses and assessments. Start small and private: run a drill with one willing colleague, keep it informal and share the result only if they wish. Once others see that the exercise takes a few minutes and produces a useful, specific comment rather than a score, resistance tends to fade. Avoid presenting it as a compliance task, since that invites box-ticking and defeats the purpose.

What length suits a drill?

Plan on a quarter of an hour, give or take. Anything longer usually drifts into general review. If you find yourself running past twenty minutes, split the exercise into two separate targets and give each its own session.

How often should I practise?

Operational duties leave room for perhaps two or three compact sessions weekly. Consistency matters more than length. A drill that fits comfortably into a quiet period is far more likely to happen than an ambitious one that depends on a free afternoon.

Is there any sign that a drill is paying off?

Choose a measure before you start and check it again afterwards. For hazard spotting, count how many of the colleague’s observations you also made. For report writing, count the questions a reader cannot answer. For risk judgement, count how many scores differ by more than one step. None of these numbers is a formal metric, and they should not be reported as performance statistics. They are personal indicators to show whether a particular drill is helping you.

Can one person run these drills alone?

Partly. Hazard spotting can be rehearsed alone by photographing an area, writing your observations, and checking them later against a fresh look. Report writing can be rehearsed by letting a draft rest overnight and rereading it as a stranger would. What a solo drill cannot give you is an outside view, which is why even an occasional ten-minute exchange with a colleague adds so much. Treat solo work as preparation and the shared exchange as the real test.

What are the common mistakes?

  • Choosing a target that is too broad. “Improve safety reporting” cannot be drilled; “include the location in every report” can.
  • Using real incident details in practice material. Use invented or published scenarios, and respect confidentiality.
  • Collecting feedback without applying it. If nothing changes on the next attempt, the feedback has not done its work.
  • Turning drills into assessments. They work best in a low-stakes setting where mistakes are expected.

Is this a substitute for formal SMS training?

No. Drills complement formal instruction; they do not replace it, and they cannot define what your organisation or regulator requires. Think of them as the rehearsal between lectures, a way of making the content you have been taught available when you need it.

What is a sensible first step?

Pick one skill from the four above, write a one-sentence target, and arrange a ten-minute session with a colleague this week. Afterwards, write down one thing you will do differently, and test it at the next opportunity. Repeat the cycle, and let the results guide what you choose to drill next.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top